Panasonic AK-UCU500 Camera Control Unit
MSRP: $15,000.00
Panasonic
Specs| Power supply | AK-UCU500P/AK-UCU500PS: 100 V - 120 V AC, 50 Hz/60 Hz AK-UCU500E/AK-UCU500ES: 100 V - 240 V AC, 50 Hz/60 Hz |
| Power consumption | 500 W (Without camera connected: 70 W) |
| Capacity for Supplying Power to a Camera | 240 V AC (tolerance: 5%), 1.46 A , 50 Hz/60 Hz |
| Operating temperature | 0°C to 40°C (32°F to 104°F) |
| Humidity | 10% to 90% (no condensation) |
| Weight | Approx. 8.8 kg (19.4 lb) |
| Dimensions (W x H x D) | 424 mm x 88 mm x 401 mm (16-5/8 inches x 3-7/16 inches x 15-13/16 inches) (excluding protrusions) |
| VIDEO OUTPUT | 3G/HD/SD-SDI: 7 lines (embedded audio is supported only for HD signals) HD/SD-SDI: 1 line (shared with picture monitor output*1 ; embedded audio is supported only for HD signals) Analog composite: 2 lines (1 line shared with picture monitor output*1) |
| HD TRUNK Output | HD-SDI: 1 line (cannot be used in UHD/HS mode) |
| Return Input | 3G-HD/HD/SD-SDI: 4 lines (RET1 input has active-through output) Analog composite: 1 line |
| Prompter Input | HD-SDI: 1 line (with active-through output) Analog composite: 2 lines (through output of 1 and input of 2 share the connector*1) It is not terminated when the unit is turned OFF. No through output. |
| Reference input | BB (black burst) / tri-level*2: 1 line (automatic termination, connect to upper connector; BB signal and tri-level signal automatically recognized, with loop-through output) |
| Microphone Output | 0 dBm/600 ohm, 2 lines (XLR, 3-pin, male) |
| Communication | Intercom input/output (ENG / PROD, 0 dBm, 600 Ω (4 W) / 1 V [p-p], 200 Ω (RTS), 4 W / RTS / CLRCOM) : 2 lines*1 PGM input (0 dBm/600 Ω) : 2 lines Tally input (red, green, yellow) : 1 input each |
| AUX | WFM control 6-bit (open collector output, terminal shared with camera microphone gain setting*1) Camera microphone gain setting input 5-bit (photo-coupler input, terminal shared with WFM control*1) Down-conversion system setting input 2-bit (photo-coupler input) |
| TRUNK | RS-422 / RS-232C 2 lines*1 |
| FRONT ROP | RS-422 1 line, 16 V DC output (only one of this and REAR ROP can be selected at one time via the menu or the [ROP FRONT/REAR] selection switch on the front panel) |
| REAR ROP | RS-422 1 line, 16 V DC output (only one of this and FRONT ROP can be selected at one time via the menu or the [ROP FRONT/REAR] selection switch on the front panel) |
| MSU | RS-422 1 line, GPI for control |
| LAN TRUNK | LAN connection with camera side via an optical cable*3 1 line, 100BASE-T, 1000BASE-T |
| LAN | Personal computer connection for distribution via the Web*3 1 line, 10BASE-T, 100BASE-TX (use a crossover cable when connecting directly with a personal computer) |
| Note | *1: Depending on the setting, only one of them can be selected at one time. *2: The BB (black burst) signal and tri-level sync signal of the reference input are recognized automatically. *3: IP video cannot be transmitted when [CCU MODE] is set to [2160/23.98p], [2160/23.98PsF], [1080/23.98p], or [1080/23.98PsF]. *4: Can be provided from CCU |
Share:
You might also like
Panasonic AG-CX350 4K Camcorder
$3,695.00
Panasonic AW-PS551 Power Supply
$695.00
Panasonic Varicam LT Pro Kit VARICAMLT-PRO
$18,595.00
