Panasonic AK-UCU500 Camera Control Unit

MSRP: $15,000.00

Panasonic

Specs

Power supply AK-UCU500P/AK-UCU500PS: 100 V - 120 V AC, 50 Hz/60 Hz
AK-UCU500E/AK-UCU500ES: 100 V - 240 V AC, 50 Hz/60 Hz
Power consumption 500 W (Without camera connected: 70 W)
Capacity for Supplying Power to a Camera 240 V AC (tolerance: 5%), 1.46 A , 50 Hz/60 Hz
Operating temperature 0°C to 40°C (32°F to 104°F)
Humidity 10% to 90% (no condensation)
Weight Approx. 8.8 kg (19.4 lb)
Dimensions (W x H x D) 424 mm x 88 mm x 401 mm (16-5/8 inches x 3-7/16 inches x 15-13/16 inches) (excluding protrusions)
VIDEO OUTPUT 3G/HD/SD-SDI: 7 lines (embedded audio is supported only for HD signals)
HD/SD-SDI: 1 line (shared with picture monitor output*1 ;
embedded audio is supported only for HD signals)
Analog composite: 2 lines (1 line shared with picture monitor output*1)
HD TRUNK Output HD-SDI: 1 line (cannot be used in UHD/HS mode)
Return Input 3G-HD/HD/SD-SDI: 4 lines (RET1 input has active-through output)
Analog composite: 1 line
Prompter Input HD-SDI:
1 line (with active-through output)
Analog composite:
2 lines (through output of 1 and input of 2 share the connector*1)
It is not terminated when the unit is turned OFF. No through output.
Reference input BB (black burst) / tri-level*2: 1 line 
(automatic termination, connect to upper connector; BB signal and tri-level signal automatically recognized, with loop-through output)
Microphone Output 0 dBm/600 ohm, 2 lines (XLR, 3-pin, male)
Communication Intercom input/output (ENG / PROD, 0 dBm, 600 Ω (4 W) / 1 V [p-p], 200 Ω (RTS), 4 W / RTS / CLRCOM) : 2 lines*1
PGM input (0 dBm/600 Ω) : 2 lines
Tally input (red, green, yellow) : 1 input each
AUX WFM control
6-bit (open collector output, terminal shared with camera microphone gain setting*1)
Camera microphone gain setting input
5-bit (photo-coupler input, terminal shared with WFM control*1)
Down-conversion system setting input 2-bit (photo-coupler input)
TRUNK RS-422 / RS-232C
2 lines*1
FRONT ROP RS-422
1 line, 16 V DC output (only one of this and REAR ROP can be selected at one time via the menu or the [ROP FRONT/REAR] selection switch on the front panel)
REAR ROP RS-422
1 line, 16 V DC output (only one of this and FRONT ROP can be selected at one time via the menu or the [ROP FRONT/REAR] selection switch on the front panel)
MSU RS-422
1 line, GPI for control
LAN TRUNK LAN connection with camera side via an optical cable*3
1 line, 100BASE-T, 1000BASE-T
LAN Personal computer connection for distribution via the Web*3
1 line, 10BASE-T, 100BASE-TX (use a crossover cable when connecting directly with a personal computer)
Note *1: Depending on the setting, only one of them can be selected at one time.
*2: The BB (black burst) signal and tri-level sync signal of the reference input are recognized automatically.
*3: IP video cannot be transmitted when [CCU MODE] is set to [2160/23.98p], [2160/23.98PsF], [1080/23.98p], or [1080/23.98PsF].
*4: Can be provided from CCU
-
+




PRODUCT DETAILS

Single 2U rack-mounted camera control unit that provides a parallel UHD and HD/SD output over a distance of 2000m

KEY FEATURES
  • Provides a parallel UHD and HD/SD outputHD output from camera (3G-SDI): 1080/59.94p, 50p, 59.94i, 50i, 29.97psF, 25psF, 23.98p over 59.94i, 720/59.94p, 50pUHD output from CCU: 2160/59.94p, 50p, 29.97p, 29.97psF, 25p, 25psF, 23.98p, 23.98psFSD output
  • Capable of optical fiber transmission of uncompressed video signals and camera power over a distance of 2000m
  • Variable Operation with Advanced Trunk functions
  • Supports IP streaming

Specs

Power supply AK-UCU500P/AK-UCU500PS: 100 V - 120 V AC, 50 Hz/60 Hz
AK-UCU500E/AK-UCU500ES: 100 V - 240 V AC, 50 Hz/60 Hz
Power consumption 500 W (Without camera connected: 70 W)
Capacity for Supplying Power to a Camera 240 V AC (tolerance: 5%), 1.46 A , 50 Hz/60 Hz
Operating temperature 0°C to 40°C (32°F to 104°F)
Humidity 10% to 90% (no condensation)
Weight Approx. 8.8 kg (19.4 lb)
Dimensions (W x H x D) 424 mm x 88 mm x 401 mm (16-5/8 inches x 3-7/16 inches x 15-13/16 inches) (excluding protrusions)
VIDEO OUTPUT 3G/HD/SD-SDI: 7 lines (embedded audio is supported only for HD signals)
HD/SD-SDI: 1 line (shared with picture monitor output*1 ;
embedded audio is supported only for HD signals)
Analog composite: 2 lines (1 line shared with picture monitor output*1)
HD TRUNK Output HD-SDI: 1 line (cannot be used in UHD/HS mode)
Return Input 3G-HD/HD/SD-SDI: 4 lines (RET1 input has active-through output)
Analog composite: 1 line
Prompter Input HD-SDI:
1 line (with active-through output)
Analog composite:
2 lines (through output of 1 and input of 2 share the connector*1)
It is not terminated when the unit is turned OFF. No through output.
Reference input BB (black burst) / tri-level*2: 1 line 
(automatic termination, connect to upper connector; BB signal and tri-level signal automatically recognized, with loop-through output)
Microphone Output 0 dBm/600 ohm, 2 lines (XLR, 3-pin, male)
Communication Intercom input/output (ENG / PROD, 0 dBm, 600 Ω (4 W) / 1 V [p-p], 200 Ω (RTS), 4 W / RTS / CLRCOM) : 2 lines*1
PGM input (0 dBm/600 Ω) : 2 lines
Tally input (red, green, yellow) : 1 input each
AUX WFM control
6-bit (open collector output, terminal shared with camera microphone gain setting*1)
Camera microphone gain setting input
5-bit (photo-coupler input, terminal shared with WFM control*1)
Down-conversion system setting input 2-bit (photo-coupler input)
TRUNK RS-422 / RS-232C
2 lines*1
FRONT ROP RS-422
1 line, 16 V DC output (only one of this and REAR ROP can be selected at one time via the menu or the [ROP FRONT/REAR] selection switch on the front panel)
REAR ROP RS-422
1 line, 16 V DC output (only one of this and FRONT ROP can be selected at one time via the menu or the [ROP FRONT/REAR] selection switch on the front panel)
MSU RS-422
1 line, GPI for control
LAN TRUNK LAN connection with camera side via an optical cable*3
1 line, 100BASE-T, 1000BASE-T
LAN Personal computer connection for distribution via the Web*3
1 line, 10BASE-T, 100BASE-TX (use a crossover cable when connecting directly with a personal computer)
Note *1: Depending on the setting, only one of them can be selected at one time.
*2: The BB (black burst) signal and tri-level sync signal of the reference input are recognized automatically.
*3: IP video cannot be transmitted when [CCU MODE] is set to [2160/23.98p], [2160/23.98PsF], [1080/23.98p], or [1080/23.98PsF].
*4: Can be provided from CCU

Recently Viewed Products